Product Details
PM-800D
Description
The POPE Professional® introduces new Class D amplifier technology offering smooth and responsive handling with massive power output while maintaining POPE Professional's famous sonic integrity. The POPE Professional PM-D Series is using SMPS technology with built in 4 in 4 out DSP, the resulting high power, lightweight units designed for install and professional touring sound applications.
The POPE Professional® PM-D Series is a range of 4 channels, high output power amplifiers. The PM-D Series has been designed to provide that, Powerful Pure Sonic Performance which is now so synonymous with the POPE Professional® brand name. With the introduction of the PM-D Series POPE Professional® aim to deliver simple, pure and reliable power for applications where cost and ease of use are paramount without lose of integrity. The PM-D Series amplifiers are having on board FIR/IIR filters, Analog In/Out, AESOP digital signal In/Out and SoundNet® Networking. The customer can add POPE Professional® SN-2 AES67 Network module or SN-4 Dante Network module at any time to enable digital networking. The SN-2 AES67 or SN-4 Dante module is an optional.
MORE INFO
PM-800D
Applications
-
- Stadium
- Concerts
- Touring events
- Clubs and Discos
- Places of worship
- Theatre and Auditorium
- Educational Institutions
Features
- Class - D Technology
- FIR / IIR Filter per Input & Output
- Four-channel flexibility
- XLR input and output connectors
- Sampling rate 96 kHz - 40 bit floating
- Up to 255 devices in one network
- 24 bit AD/DA converters
- X-Over, Dynamic / RMS / PEAK Limiters
- 24 Presets
- AES67 / Dante / AESOP Digital Input
- Supplied with SoundNet® Networking GUI
Power Output
Model | Total Channels | 4Ω Per Channel | 8Ω Per Channel | 4Ω Bridged | 8Ω Bridged | 70/100V |
PM-500D | 4 | 500W | 250W | 2*1250W | 2*1250W | 2*800W |
PM-800D | 4 | 800W | 400W | 2*2500W | 2*1600W | 2*1600W |
PM-1250D | 4 | 1250W | 1250W | - | - | 4*800W |
PM-2500D | 4 | 2500W | 1600W | - | - | 4*1600W |
Specifications
THD | < 0.05 % (20 Hz - 20 kHz, 8Ω load, 3 dB below rated power) |
Signal-to-Noise Ratio | > 120 dB (A-weighted, 20 Hz - 20 kHz, 8Ω load) |
Frequency Response | 20 Hz - 20 kHz Ω ± 0.25 dB / 20 Hz - 20 kHz Ω ± 0.15 dB (8Ω load, 1 dB below rated power) |
Output Circuitry | Class D - full bandwidth PWM modulator with ultra low distortion |
Input impedance | 15k balanced |
Damping Factor | > 2000 (8Ω load, 1 kHz and below) |
| |
Digital Signal Processor |
|
In/Out | 4 In / 4 Out |
DSP | 40 bit / 96kHz DSP |
Filters | FIR / IIR, Frequency, Gain, RMS, Peak, Dynamic Limiter |
Analog Signal | Balanced Input / Output |
Digital Signal | Dante® / AES67 / AESOP (SN-2 AES67 / SN-4 Dante Module - Optional) |
Connectors | XLR male / female and Ethernet |
Control | Ethernet - SoundNet® Networking |
Preset | 24 |
| For more specifications about DSP, check the XT-4040 product catalogue. |
|
|
Connectors and Switches |
|
Input connectors (per ch) | 3-pin XLR, electronically balanced |
Output connectors (per ch) | 3-pin XLR, electronically balanced |
Amplifier Output | 4 Pin Speakon 1: +1-1 CH-1, +2-2 CH-2, 4 Pin Speakon 2: +1-1 CH-2, |
| 4 Pin Speakon 3: +1-1 CH-3, +2-2 CH-4, 4 Pin Speakon 4: +1-1 CH-4 |
Power on/off | on front-panel switch |
Cooling | Fans, front-to-rear airflow |
Front Panel Indicators |
|
Display | OLED Display |
Per channel | Signal / Clip / Protect |
|
|
Safety |
|
Protection Circuits | Input limiter, short circuit protection, DC protection of output, under & over voltage protection, SOA protection, intelligent mains fuse protection, power stage overload protection, temperature protection for transformer |
|
|
Power |
|
Type | Universal & regulated switch mode power supply with Power Factor Correction |
Operating voltage | Universal Mains, 90-270V AC |
Mains | Power Cord |
Model | PM-500D | PM-800D | PM-1250D | PM-2500D |
Amplifier Dimension | 482 mm x 485 mm x 88 mm (W x D x H) | 482 mm x 550 mm x 88 mm (W x D x H) | ||
Packing Dimension | 535 mm x 555 mm x 195 mm (W x D x H) | 535 mm x 615 mm x 195 mm (W x D x H) | ||
Size | 2U | |||
Net Weight | 9.30 kg | 9.60 kg | 13.80 kg | 14.30 kg |
Gross Weight | 10.80 kg | 11.10 kg | 15.70 kg | 16.20 kg |
Note:
1) All specifications are typical values.
2) The amplifier will be fully operational at 2 ohm loads, but due to physical constraints in the construction, this mode of operation is not recommended.
3) The PM-500D & PM-800D amplifiers have to select bridge mode for 70/100V operation.